Liquor Lollipops Recipe 395

Steps:

• If you don't have lollipop molds, place a silicone mat on a baking sheet. Mix together 1/4 cup of the liquor, and the water, sugar, corn syrup, and salt in a 1- or 2-quart saucepan until all of the sugar is wet. If sugar crystals cling to the sides of the pan, dissolve them away with a wet pastry brush. Bring the mixture to a boil over medium heat, stirring occasionally and gently with a heatproof spatula until all of the sugar is dissolved. Then boil to 300°F (149°C) without stirring. Remove from the heat, and, working quickly, mix in the remaining 1 teaspoon liquor and food coloring, if using. Still working with haste, drop the syrup into either lollipop molds or onto a silicone mat. If using lollipop molds, quickly drop the syrup from the tip of a large spoon into the cavities of the lollipop molds. Place a lollipop stick in the center of each disk, and twist it 180 degrees so that it's fully covered in syrup. Let cool completely. If using a silicone mat, quickly drop the syrup onto the silicone mat so that it forms 2-inch disks and immediately after plopping the syrup on the sheets place a lollipop stick in the center of each disk and twist it 180 degrees so that it's fully covered in syrup. Let cool completely. Peel the lollipops from the molds or silicone and store in an airtight container, preferably at least overnight to allow the flavors to develop, until ready to indulge.

Steps:

• If desired, add nuts to any or all of the chocolates. Pour the chocolate into the molds, filling them to the top. Set the sticks in place by inserting them just far enough to be secure within the mold you are using. Set the molds aside to allow the chocolate to set. When set, simply pop out the lollipops. If you are using molding compound, roll it into a 1/2-inch-thick rectangle on top of a sheet of parchment paper. Using a sharp paring knife, cut out whatever shapes you would like and remove the cutout, leaving the homemade mold. Spray the inside edge of the molding compound with vegetable cooking spray and pour the chocolate into the cut out space. Insert the lollipop sticks and let cool completely before removing the molding compound. When finished, the molding compound can be saved and reused for another day.
• How to Temper Chocolate (From Dessert Circus, Extraordinary Desserts You Can Make At Home by Jacques Torres): Chocolate is tempered so that after it has been melted, it retains its gloss and hardens again without becoming chalky and white (that happens when the molecules of fat separate and form on top of the chocolate). There are a variety of ways to temper. One of the easiest ways to temper chocolate is to chop it into small pieces and then place it in the microwave for 30 seconds at a time on high power until most of the chocolate is melted. Be very careful not to overheat it. (The temperature of dark chocolate should be between 88 and 90 degrees F, slightly warmer than your bottom lip. It will retain its shape even when mostly melted. White and milk chocolates melt at a temperature approximately 2 degrees F less because of the amount of lactose they contain.) Any remaining lumps will melt in the chocolate's residual heat. Use an immersion blender or whisk to break up the lumps. Usually, chocolate begins to set, or crystallize, along the side of the bowl. As it sets, mix those crystals into the melted chocolate to temper it. A glass bowl retains heat well and keeps the chocolate tempered longer. Another way to temper chocolate is called seeding. In this method, add small pieces of unmelted chocolate to melted chocolate. The amount of unmelted chocolate to be added depends on the temperature of the melted chocolate, but is usually 1/4 of the total amount. It is easiest to use an immersion blender for this, or a whisk. The classic way to temper chocolate is called tabliering. Two thirds of the melted chocolate is poured onto a marble or another cold work surface. The chocolate is spread out and worked with a spatula until its temperature is approximately 81 degrees F. At this stage, it is thick and begins to set. This tempered chocolate is then added to the remaining non-tempered chocolate and mixed thoroughly until the mass has a completely uniform temperature. If the temperature is still too high, part of the chocolate is worked further on the cold surface until the correct temperature is reached. This is a lot of work, requires a lot of room, and makes a big mess. A simple method of checking tempering, is to apply a small quantity of chocolate to a piece of paper or to the point of a knife. If the chocolate has been correctly tempered, it will harden evenly and show a good gloss within a few minutes.